Are you on the lookout for tips on A Step-by-Step Guide to Installing a Bathtub?
Setting up a bath tub isn't precisely brain surgery, however it does call for solid plumbing, woodworking, as well as sometimes, tiling skills. Replacing an old bath tub with a new one is also a reasonably challenging project. If the old bathtub is easily accessible, the job can move easily; if you have to open up a wall to remove the old bathtub and place the new bath tub, the job is much harder. In either situation, the project is within a residence handyman's skills, although you will certainly need an assistant to leave the old tub and embeded in the new one. See to it you have certified yourself for the task and fit attempting it. As opposed to employing a contractor to take over a halfway-completed project, it is much better to consider utilizing one prior to you begin. Opportunities are you may require a professional plumber to make tube links.
This article will aid you install a brand-new bathtub in your shower room if you have actually already gotten a brand-new tub and also do not need to alter the arrangement of your previous water pipes.
Your devices and product checklist need to make up the following:
Preparing for the Setup
Firstly, the sustaining structure supplied with the bathroom ought to be fitted (if called for) according to the manufacturer's directions. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is important to ensure that if the faucet comes with a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps system to stop strain on the tub.
Fit the adaptable faucet adapters to the bottom of the two taps making use of 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you make use of every one of the supplied washers.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath must currently be ready to be fitted in its last placement.
Removing Old Taps
If you need to change old faucets with new ones as a part of your installation, after that the first thing you need to do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any water remaining in the system. The process of getting rid of the existing taps can be rather bothersome as a result of the restricted access that is typically the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the taps. Have a cloth prepared for the staying water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning during this process. Once the taps have been removed, the holes in the bath/basin will have to be cleaned of any old sealing compound.
Before moving on to fit the new faucets, compare the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the new taps to fit.
Setting up the Tub
Making use of both wood boards under its feet, position the bath tub in the called for position. The wooden boards are useful in evenly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto four little points.
The next goal is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the tub up until the spirit level reads level.
To install faucets, fit all-time low of the outermost adaptable faucet port to the proper supply pipe by making a compression join; then do the same for the various other faucet.
Activate the water system as well as inspect all joints as well as new pipework for leaks and also tighten them if essential. Fill up the tub and also examine the overflow electrical outlet as well as the typical outlet for leakages.
Lastly, repair the bathroom paneling as explained in the producer's instruction manual. Tiling and securing around the tub ought to wait till the bath tub has been used at the very least when as this will certainly settle it right into its last setting.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end offers a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly require decreasing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, position the tap in the placing hole in the bath/basin ensuring that the washing machines are in area between the faucet as well as the sink. Safeguard the tap in position with the maker provided backnut. As soon as the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The previous type must be connected to the faucet finishes first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bathroom fulfills the tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate enough to break a stiff seal, causing the water to penetrate the wall in between the bath as well as the tiling, leading to problems with wetness and also feasible leaks to the ceiling below.
You can select from a selection of coloured sealers to blend in your components and also installations. They are sold in tubes and cartridges, and are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of soaked paper or soft rope. Bear in mind to always fill up the tub with water prior to securing, to allow for the motion experienced when the bathtub remains in usage. The sealant can break relatively very early if you do not take into account this movement before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently readily available on the marketplace. It is advisable to fit the tiles using waterproof or waterproof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were shown that editorial about Installing A Bathtub through a good friend on a different blog. Sharing is nice. You won't know, you might be helping someone out. Thank-you for taking the time to read it.
Get Started